How to Clean Dyson Airwrap Filter: Simple Steps for Peak Performance
Cleaning your Dyson Airwrap filter helps keep its performance strong. Remove the filter cage by twisting it off gently. Rinse the filter under warm water to wash out hair and dust particles.
If you notice heavy buildup, soak the filter cage in warm, soapy water for 30 minutes. Add a drop of dish soap or clarifying shampoo to break down oils and residues. Rinse thoroughly after soaking to remove any soap leftover.
Let the filter dry completely in open air before reinstalling it. This usually takes about 24 hours to avoid moisture damage or clogging. Never put the filter back while it is still damp to keep your Airwrap working well.
Cleaning the filter regularly helps your Airwrap run smoothly and extend its life. It also prevents strange smells or overheating during use. Make this part of your usual Airwrap maintenance routine for the best results.
Key Takeaways
- Remove and rinse the Dyson Airwrap filter cage under warm water every two weeks.
- Use warm soapy water soak for 30 minutes to clear stubborn residue.
- Allow the filter to air dry fully for at least 24 hours before reattaching.
- Clean the filter more often if you use your Airwrap daily.
- Don’t reattach a damp filter cage to avoid device damage.
- Check filter cleanliness if airflow feels weak or performance drops.
How to Clean Your Dyson Airwrap Filter Step-by-Step

Cleaning your Dyson Airwrap filter is simple and helps keep your device working well. You remove the filter cage, rinse it, soak if needed, dry fully, and then reattach it. Each step ensures your Airwrap stays safe and effective.
Removing the Filter Cage from the Device
Before you start cleaning, unplug your Dyson Airwrap for safety. The filter cage is located at the base of the device. You can twist off the cage by turning it gently counterclockwise.
Give the cage a slow, steady twist until it releases. Avoid forcing it to stop damage.
Once loose, carefully pull the cage away from the Airwrap. Watch out not to lose any small parts during removal.
Rinsing and Soaking the Filter Cage
Hold the filter cage under cool running water to wash off dust and hairs. Rinse until the water runs clear and you see no visible dirt.
Grime may stick on the cage. Soak it about 30 minutes in warm water with mild dish soap.
Add a few drops of clarifying shampoo to the soak to remove buildup. After soaking, scrub gently with a soft brush or cloth. Avoid using hot water or harsh cleaners that could damage parts.
Drying the Filter Cage Completely
After rinsing or soaking, give the filter cage a quick shake to remove extra water. Set it somewhere clean and dry, letting it air dry for at least 24 hours. Never dry with heat, towels, or hair dryers as this risks damage.
The cage needs to be absolutely dry before using it again. A damp filter can cause your Airwrap to overheat or stop working properly. Leaving it out a full day usually ensures it’s fully dry.
Reattaching the Filter Cage Securely
Once the cage is dry, line it back up with the Airwrap base. Gently place the cage back onto the device.
Twist it clockwise until you hear a click or feel it lock securely. Make sure it is secure but don’t press down hard to avoid cracking it.
Check the cage is seated evenly and doesn’t wiggle after reattachment. Proper positioning helps your Airwrap run smoothly and prevents dust entry. Keep the cleaned filter cage dry and stored in a clean place between uses.
- Unplug your Dyson Airwrap before cleaning.
- Twist the filter cage counterclockwise to remove it carefully.
- Rinse the cage under cool running water until clear.
- Soak the cage in warm soapy water for 30 minutes if dirty.
- Gently brush any remaining dirt off the filter cage.
- Let the filter cage air dry completely for 24 hours.
- Align and twist the dry filter cage clockwise onto the device.
- Ensure the cage clicks firmly into place before using the Airwrap.
Signs You Need to Clean Your Dyson Airwrap Filter Now

Keep an eye on the LED lights on your Dyson Airwrap. A flashing white light usually means the filter needs cleaning.
Some models with Bluetooth show additional signals. But most will alert you clearly when airflow is hindered.
When the filter gets clogged, airflow drops and the device heats up. You might notice the Airwrap feels hotter than usual or shuts down unexpectedly to avoid damage. That’s the motor protecting itself, so don’t ignore it.
Reduced styling power is a common sign of a dirty filter. Your hair won’t style as smoothly or quickly. You might hear strange sounds like buzzing or whirring.
Dust inside can also cause a faint burning smell. These are signs of dust build-up.
- Flashing white LED light signals filter cleaning time
- Weaker airflow during operation
- Device overheating or automatic shut-off
- Longer styling time and less effective results
- Unusual noises like buzzing or whirring
- A faint burnt or dust smell from the device
Ignoring these signs can lead to poor performance and shorten the Airwrap’s lifespan. Filters normally need cleaning about once a month based on use. Regular checks let you catch problems early and keep styling trouble-free.
Don’t let the filter clog too much. It causes overheating and reduces styling power quickly.
Notice frequent shutdowns or poor airflow after cleaning? The filter might need to be replaced. Dyson sells genuine filters for about $20.
Third-party options with cleaning brushes cost less. Watching for these signs keeps your Airwrap running smoothly and your hair looking great.
Tools and Preparation Needed Before Cleaning the Filter
Dyson includes a soft filter cleaning brush with every Airwrap. This small brush fits neatly for easy debris removal. Use a dry toothbrush with soft bristles as a backup tool.
You’ll need warm water to rinse the filter. But avoid any water on the main machine parts.
A mild detergent or gentle soap is optional for more thorough cleaning. Shampoo isn’t recommended because it can leave residue behind.
Prepare a clean, dry towel to rest the filter on after rinsing. It helps catch drips and keeps the surface protected. Pick a well-ventilated spot to dry the filter.
Leave it there for 24 hours. This helps stop moisture inside the device.
- Soft filter cleaning brush (included with Airwrap) or dry toothbrush
- Warm water for rinsing
- Mild detergent or gentle soap (optional)
- Clean, dry towel to place the filter on
- Dry, well-ventilated area for air drying, away from direct sunlight
Keep your workspace away from liquids or clutter. This prevents accidental spills or damage to your Airwrap. Clear enough room so you can easily reach water and towels without rushing.
Do not use compressed air or vacuum cleaners to clean the filter. These can damage delicate parts or push debris further inside. Follow the soft brush and water method to avoid harm and get the best results.
How Often Should You Clean the Dyson Airwrap Filter?
Daily users should clean the Dyson Airwrap filter every two weeks to keep airflow steady. This frequency helps avoid clogging from styling product buildup and oils. Skipping cleanings can reduce suction power and strain the motor over time.
For occasional users, monthly cleaning usually works well. It stops dirt and dust from blocking airflow during use. This works well if you style your hair just a few times a week.
For less frequent use, it’s enough to keep the airflow clear. But if you use hairspray or heavy styling products, you might want to clean more often.
Deep cleaning becomes necessary when debris stubbornly sticks in the filter mesh. This might happen every few months for daily users or after heavy product buildup. It involves more thorough rinsing and gentle scrubbing compared to the usual dust removal.
Your hair type and styling routine also affect how often you clean. Thick or oily hair sheds more, which clogs the filter faster.
Using heat protectants or oil-based products can increase residue. So adjust your cleaning schedule accordingly.
- Clean every two weeks if you style daily with many products
- Monthly cleaning suits light or occasional use
- Deep clean if normal cleaning doesn’t remove all buildup
- Oily or thick hair users should clean more frequently
- Adjust based on how often and how much product you apply
Delaying cleaning risks reduced airflow, longer drying time, and uneven styling. The filter may also overheat and damage internal parts. Consistent cleaning keeps your Airwrap working well and extends its lifespan.
Keep an eye on airflow and temperature changes during use. These signs tell you when the filter needs cleaning sooner than planned.
Cleaning is quick and costs nothing except your time. So try to stay ahead of any issues.
Deep Cleaning for Stubborn Filter Buildup: What to Do
Move to deep cleaning if your Dyson Airwrap filter feels clogged. A simple rinse may not remove all the grease. Deep cleaning loosens stuck buildup and freshens the filter.
Sticky buildup often comes from styling products, needing more attention. Deep cleaning removes stubborn grease safely with soaking, soap, and gentle brushing.
Preparing a Soaking Solution
Use lukewarm water for soaking your filter to avoid warping or damage. Put a few drops of mild dish soap in warm water.
You can use clarifying shampoo instead to break down grease. Soaking helps remove product and oil better than water alone.
Mix about one teaspoon of soap into one cup of water. This gentle solution cleans without harming filter material or fine mesh.
Soaking Duration and Temperature
Let the filter soak in the warm soapy water for about 10 minutes. This loosens stubborn oils and styling residues.
Water should not be hotter than 100°F (38°C) to protect filter parts. Avoid soaking longer than 15 minutes to prevent potential damage.
Gentle Brushing Techniques for Residue
Use a soft brush or the Dyson filter cleaning tool to remove loosened residue. Be gentle to protect the mesh and avoid tearing.
Brush in small circles over the sticky areas. Don’t scrub harshly; that may damage the filter structure or push debris further in.
Rinsing and Drying After Deep Cleaning
Rinse the filter under cool running water to wash away soap and loosened dirt. Shake lightly to remove excess water.
Dry the filter fully for at least 24 hours before reinstalling. Placing it in a warm, well-ventilated spot speeds up drying without heat damage. Follow these steps for a proper deep clean when your filter sticks or clogs:
- Remove the filter cover and carefully pull out the filter.
- Mix lukewarm water with a teaspoon of mild dish soap or clarifying shampoo.
- Soak the filter in the solution for about 10 minutes at max 100°F (38°C).
- Use a soft brush or Dyson cleaning tool to gently scrub away grease or buildup.
- Rinse the filter well under cool running water to remove soap and debris.
- Shake off excess water and place the filter on a clean towel in a ventilated area.
- Allow the filter to dry completely for at least 24 hours before putting it back.
Never soak the filter longer than 15 minutes or use hot water over 100°F. This can damage the filter. Avoid harsh scrubbing to keep the mesh intact and working well.
Common Mistakes to Avoid When Cleaning Your Dyson Airwrap Filter
Don’t use compressed air or vacuum cleaners with strong suction on your Dyson Airwrap filter. Compressed air can force dust deeper inside the filter or damage delicate parts. Vacuum cleaners can work.
Avoid high power settings. They may damage the filter cage or mesh.
Using harsh chemicals or soaps is another big mistake. These can break down the filter fibers or cause build-up that clogs airflow.
Stick to gentle washing with lukewarm water only. Never add bleach, alcohol, or detergent, which risks permanent damage.
Reattaching the filter when it’s still wet can cause serious trouble. Moisture inside the device can rust metal parts or cause electrical shorts.
Always let the filter dry completely, this can take several hours at room temperature. Don’t speed drying with a hairdryer or heater either.
The filter cage is fragile, so handle it carefully. Avoid twisting or pulling the filter hard as you remove it. That can bend or crack the cage.
Instead, gently press release buttons or tabs before sliding the filter out straight. This keeps it fit snugly back in place when done.
- Use only lukewarm water to rinse the filter gently
- Do not spray or blow compressed air into the filter
- Vacuum only on a low suction setting and carefully
- Never use bleach, detergents, or alcohol-based cleaners
- Remove the filter by pressing release tabs without twisting
- Let the filter dry fully in air, no heaters or dryers
- Check the filter cage for cracks or bends before reinserting
Handling the filter this way keeps your Dyson Airwrap safe and working well. Damaged or clogged filters reduce airflow and can overheat your device. Taking these simple steps avoids costly repairs or replacing the styler too soon.
Troubleshooting When Cleaning Doesn’t Fix Your Airwrap
Your Dyson Airwrap may still have weak airflow, overheat, or show error lights despite cleaning. Try resetting the device and checking for blockages or damage. When problems continue, contact Dyson support or get a replacement filter.
Resetting Your Dyson Airwrap
Resetting can clear error lights or temporary glitches after cleaning. This helps the device recognize the cleaned or replaced filter and resume normal function. Follow these steps to reset your Dyson Airwrap:
- Turn off the Airwrap and unplug it from the power outlet.
- Wait at least 10 seconds before plugging it back in.
- Press and hold the power button for 5 seconds.
- Release the button and wait for any indicator lights to stop blinking.
- Turn the Airwrap back on and test airflow and heat.
This quick reset can help fix weak airflow and stop error signals. Should it still not turn on, proceed with more troubleshooting steps.
Inspecting for Physical Damage or Blockage
Check the Airwrap for any cracks, dents, or blocked air intakes. Damage to filters or attachments causes weak airflow or overheating. Look closely at:
- Filter housing and attachments for cracks
- Air inlets to spot dust clogs or hair buildup
- Power cord and plug for damage or looseness
Even with a clean filter, blockages inside the unit or damaged parts reduce performance. Reattach parts firmly before testing again.
Contacting Dyson Support or Repair Services
When the Airwrap still malfunctions, contact Dyson support or use warranty services. They can confirm if your device needs a replacement filter or other service. Reach Dyson through:
- Visit the Dyson website’s support section.
- Use the online troubleshooting tool for quick fixes.
- Call Dyson customer service for direct assistance.
- Check your product warranty status before repair requests.
- Arrange for mail-in repair or authorized service center visit.
Replacement filter costs vary by model but usually range from $20 to $50. Always use official parts to avoid damage.
Preventive Tips to Keep Your Dyson Airwrap Filter Cleaner Longer
Store your Dyson Airwrap in a clean, dry space to cut down dust buildup. Avoid places where construction dust or pet hair hangs in the air. Keeping it in a drawer or a case helps keep particles away from the filter.
Styling habits influence how fast the filter clogs. Use hair products sparingly near the Airwrap’s air intake.
Oils, sprays, and powders can stick to the filter and cause buildup. Brush your hair before styling to remove loose strands that might get trapped.
Check the filter every 1 to 2 weeks if you use your Airwrap daily. Lightly brush the filter with a small dry brush or duster. This stops dirt from building up between cleanings.
Do this regularly to keep it clear. This quick habit keeps airflow strong without deep cleaning each time.
Do not wash the filter with water unless cleaning fully. Water can damage your device if you do not clean it right. Follow the full cleaning steps first.
Environmental factors affect how quickly your filter gets dirty. City air, smoking, pet presence, or smoky kitchens load more particles on your filter. Increase brushing if your space is dusty or polluted often.
Clean the filter more than usual to protect your device. This helps avoid buildup and damage.
- Keep your Airwrap stored away from open windows or vents
- Use hair products moderately and avoid the air intake area
- Brush your hair thoroughly before styling
- Dust or brush the filter weekly if using Airwrap regularly
- Increase filter cleaning frequency in dusty or smoky spaces
- Use no liquid or sprays directly on or near the filter
- Keep a small cleaning brush with your styling tools for regular care
There are no special products made specifically for maintaining the Airwrap filter’s health. Avoid sprays or oils near the filter to limit buildup. Dry brushing and storing properly add life to your filter.
These simple steps keep your Airwrap running at full power. Do them regularly for best results.
Step-by-Step Action Plan
Follow this simple plan to clean your Dyson Airwrap filter effectively. It will keep your device working well and avoid damage.
- Before You Start: Unplug the Airwrap and let it cool down. This prevents burns and electrical issues.
- Week 1: Remove the filter cage by twisting it gently. Check that no visible dust or hair clogs remain.
- Week 1: Use a soft brush or a dry cloth to clean filter mesh. You’ll see less dust and better airflow afterward.
- Week 2: Rinse the filter cage with cold water if buildup is stubborn. Let it dry completely for 24 hours before reuse.
- After 2 Weeks: Reassemble the filter cage firmly to avoid gaps. Run the device briefly to confirm airflow feels smooth.
- Monthly Check: Look for warning lights or weaker airflow. These signs mean another cleaning is needed soon.
- If Airflow Is Still Weak: Inspect the barrel and attachments for clogs. Clean those by wiping with a damp cloth.
Frequently Asked Questions
How Do I Know the Dyson Airwrap Filter Needs Cleaning?
The Dyson Airwrap shows a flashing white light when the filter needs cleaning. Weak airflow or the device not working well also means it’s time to clean the filter. Keep an eye on these signs to avoid performance issues.
Can I Use Compressed Air to Clean My Dyson Airwrap Filter?
No, using compressed air is not recommended for cleaning the Dyson Airwrap filter. It can damage the filter material or push dust deeper inside. Stick to gentle rinsing with water for safe cleaning.
Is It Safe to Clean the Dyson Airwrap Filter with Water?
Yes, cleaning the Dyson Airwrap filter with water is safe and effective. Use lukewarm water to rinse away dust and debris carefully. Let it dry completely before reattaching to avoid damage.
How Often Should I Clean My Dyson Airwrap Filter If I Use It Daily?
Clean your Dyson Airwrap filter at least every two weeks if you use it daily. Regular cleaning prevents clogs and overheating. Less frequent use means you can clean monthly.
Can a Dirty Dyson Airwrap Filter Cause the Device to Overheat?
Yes, a clogged filter can block airflow, causing the Dyson Airwrap to overheat. Overheating can damage the device and affect styling results. Clean the filter regularly to avoid this problem.
What Should I Do If Cleaning the Filter Doesn’t Fix My Dyson Airwrap?
If cleaning the filter doesn’t help, check for blockages in other parts or call Dyson support. Faulty motors or wiring could also cause issues. Professional help might be necessary.
Key Points to Remember
Cleaning your Dyson Airwrap filter helps it run smoothly and lasts longer. Pay attention to signs that need cleaning. Take action now by gently removing and brushing the filter cage dry.
